Phone Blaster 14.4

CT3110

Creative's Phone Blaster uses a single chip Sound Blaster solution and incorporates modem functions which is fully Sound Blaster compatible, Roland MPU401 UART mode compatible with Multimedia PC Level 1 specifications. It makes an ideal platform for the widest possible applications.

General
Hardware Specifications
Hardware Settings
External Connectors
CD-ROM Interface

GENERAL

System Requirements:
- IBM PC 386DX and higher or 100% compatibles
- EGA or VGA card (VGA recommended)
- 4 MB system memory (minimum)
- DOS 5.0 and above
- Windows 3.1 for Windows applications
Computer Bus Size: 16 bits
AD/DA Resolution: 16 bits
Output Power (Max.): 4 Watts @ 4 Ohms PMPO
FM Synthesis: Yes
Built-In Stereo Power Amplifier: Yes
Built-In Digital/Analog Mixer: Yes
Modem Capability: Yes

HARDWARE SPECIFICATIONS

(SOUND BLASTER SECTION)

Frequency Response: 20Hz - 20KHz (Line-out)
Signal to Noise Ratio: 80 db (Line-out)
Total Harmonic Distortion @ 1 Vrms: 0.07% (Line-out)
Sampling Rate for Playback/Recording (Stereo): 5 KHz - 44.1 KHz
Mixer Volume Control (for PC Speaker): 4 levels @ 6 db per step
Mixer Volume Control (for other sources): 8 levels @ 2 db per step
Bass and Treble Control: No
Supply Voltage Requirement (Loading): +5, +12, -12 Volt
Current Consumption (Typical): 500, 500, 50 mA respectively
Microphone Impedance: 600 Ohms
Line-In Impedance: 10 KOhms
CD Audio-In Impedance: 10 KOhms
Microphone Sensitivity: 10 - 200 mVpp
Line-In Sensitivity: 0 - 2 Vpp
CD Audio-In Sensitivity: 0 - 2 Vpp

(MODEM SECTION)

Data Mode
- Data throughput up to 57.6 kbps
- Supports CCITT V.32 bis, V.32, V.22bis, V.22A/B, V.23 and V.21
- Supports Bell 212A and 103
- V.42 LAPM and MNP2-4 error correction
- V.32bis and MNP5 data compression
Fax Mode
- Supports CCITT V.17, V.29, V.27ter and V.21 channel 2
Voice Mode
- Enhanced ADPCM compression/decompression
- Tone detection/generation and call discrimination
- Concurrent DTMF detection
Speakerphone Mode
- Full-duplex speakerphone with acoustic and line echo cancellation
- Microphone volume control and muting
- Speaker volume control and muting
- Auto fallback to pseudo-duplex

HARDWARE SETTINGS

Default settings are shown in [brackets]

Interrupt (IRQ): 2, [5], 7, 10

 IRQ:     2    5     7     10
 IS0      ON   OFF   ON    OFF
 IS1      ON   ON    OFF   OFF

8-bit DMA Channel: 0, [1], 3

 Channel:    0      1       3
 DAS0        ON     OFF     ON
 DAS1        ON     ON      OFF

16-bit DMA Channel: [5], 6, 7

 Channel     5      6       7
 DBS0        ON     OFF     ON
 DBS1        ON     ON      OFF

Joystick I/O Address: 200 Hex

Audio I/O Address: [220], 240, 260, 280 Hex

 ADDRESS:  220     240     260     280
 IOS0      ON      OFF     ON      OFF
 IOS1      ON      ON      OFF     OFF

MPU-401 I/O Address: 300, [330] Hex

 Port address:  300     330
 MSEL           OFF     ON

FM Synthesizer I/O Address: 388 Hex
Wave Synthesizer I/O Address: Not applicable

IDE Interface Port: Secondary, [Tertiary], Quaternary

 Port:    Secondary  [Tertiary]  Quaternary
 IDE100      ON         OFF        OFF
 IDE101      OFF        ON         OFF

IDE Interface IRQ: [10], 11, 12, 14, 15
Modem Interrupt (IRQ): 3, 4, 10, [11]

Modem Address: 3F8 Hex (COM 1), 2F8 Hex (COM 2), [3E8 Hex] (COM 3), 2E8 Hex (COM 4)

 COM Port:   COM1  COM2  COM3  COM4
 CS0         ON    OFF   ON    OFF
 CS1         ON    ON    OFF   OFF

EXTERNAL CONNECTORS

Line-In: Yes
Mic-In: Yes
Line-Out: Yes
Speaker-Out: Yes
PC Speaker-In: Yes
Game/Joystick Port: Yes
CD-ROM Audio-In (SB Audio Socket): Yes
CD-ROM Audio-In (MPC2 Socket): Yes
Wave Blaster Daughter Board Connector: Yes

CD-ROM INTERFACE

IDE Interface: Yes
Creative/Panasonic Interface: No
Mitsumi Interface: No
Sony Interface: No